Showing posts with label controller. Show all posts
Showing posts with label controller. Show all posts

Friday, December 20, 2013

Automatic Water Level Controller

Water-level controllers are common nowadays. The one described here is built around timer NE555 and inverter buffer CMOS IC CD4049. It uses readily-available, low-cost components, and is easy to build and install on the over-head tank (OHT) to prevent wastage of water. The circuit works off a 12V battery or 230V AC mains using a 12V adaptor. The three sensors built from non-corrosive metal are fitted to the OHT as shown in Fig. 2 and connected to the circuit (Fig. 1) at appropriate terminals.

Automatic Water-Level Controller Circuit Diagram
Automatic Water-Level Controller Circuit Diagram

Power supply terminal Vcc is at the bottom of the tank, sensor terminal L is just above the bottom of the tank and sensor terminal H is at the top of the tank. After you have properly installed the sensors in the OHT and connected the power supply, the circuit is ready to use. Since Vcc terminal is at the bottom of the tank, when the water level falls below sensor L, timer IC2 is triggered at pin 2 via inverters N1 and N2 and its output goes high. As a result, the output of timer IC2 goes high. Relay RL1 energises and the motor starts filling water in the tank.

Automatic Water-Level Controller Circuit Diagram
Automatic Water-Level Controller

The motor remains ‘on’ even when the water level crosses sensor L. As water in the tank rises to touch sensor H, timer IC2 is retriggered at pin 6 via inverters N3 and N4 and as a result, its output goes low. The relay de-energises and the motor stops filling water in the tank. The motor remains ‘off’ even when the water level falls below sensor H. As water is consumed and its level falls below sensor L, the motor restarts. Thereafter, the cycle repeats. You can also manually start and stop the motor using switch S1.

Read More..

Saturday, August 31, 2013

TDA7275A DC Speed Controller

Using the TDA7275A linear integrated circuit manufactured in a minidip plastic package can be designed a very simple speed regulator electronic project that can be used for speed regulation of small DC motors .


TDA7275A DC Speed Controller Schematic


TDA7275A DC speed controller project is intended for use as speed regulator for DC motors of record players, tape and cassette recorders. This DC motor speed controller circuit project can provide a maximum output current of 1.5 amperes .

This circuit can be powered with a voltage range between 8 and 18 volts . V2 is typically 1.5 volt for Motor ”Run” (Acc. Following data or open) and 1 volt for Motor ”Stop” (Acc. Following data or grounded) .
Read More..

Thursday, August 8, 2013

Automatic room light controller




This
circuit is called the auto circuit which can use any electronic device
to operate it automatically. To make this circuit the cost is very low.
Any interested student can make it very easily. The main component of
this circuit is transistor. Its operation is very easy. 

The
main purpose of this is to operate a charger fan where need 6volt
battery. This circuit is mainly needed when the main power is OFF. That
is called load shedding. Because at the time of  load shedding , 6volt
battery operate the fan automatically. You don’t have need to ON the
switch of the fan or OFF the fan switch. Only relay work this as a
switch. The charging system is also automatically. On the other big
matter is that no over charge is occurred of the battery. So the life
time of the battery is increased.

Component:
1.      Transistor ( npn ) – 2N2222, BC547
2.      Zener Diode - 6.8V
3.      Diode
4.       Relay - 6V
5.      Resistor – 1K, 100Ω
6.      Rechargeable Battery - 6V
7.      Bulb - 6V
8.      Power supply - 6V

Operation:
This
circuit is three section, input section and output section. 2N2222
transistor is used to control relay. BC547 transistor is used to control
output section using relay. Zener diode and a diode connect with BC547
transistor base as a series connection. Zener diode always controls
battery charge. It zener voltage is 6.8V which can’t overcome battery
voltage.
When
power supply voltage is applied to the 2N2222 transistor base the
transistor is on. So the relay is ON relatively the output circuit is
OFF. Inverse will occurs when power supply voltage is OFF. When 2N2222
transistor is ON then relay active only battery charging, relay
deactivate the fan. Zener diode always keeps battery voltage full
(6volt).
Advantages:
1.      Need not switch ON/OFF.
2.      It depends on AC power supply come or gone.
3.      This circuit is used when you are sleeping.
4.      Easy to make
5.      Cost is very low
6.      Components are few.
7.      Battery can’t over charge.
8.      Overall efficiency is 78%.
9.      Not you, only relay can do your work.
10.  The circuit is a small project for all students.
 
Read More..

Sunday, May 5, 2013

Heater Controller

Minuscule circuit of the electronic heater controller presented here is built around the renowned 3-Pin Integrated Temperature Sensor LM35 (IC1) from NSC. Besides, a popular Bi Mos Op-amp CA3140 (IC2) is used to sense the status of the temperature sensor IC1, which also controls a solid-state switch formed by a high power Triac BT136(T1). Resistive type electric heater at the output of T1 turns to ON and to OFF states as instructed by the control circuit.

This gadget can be used as an efficient and safe heater in living rooms, incubators, heavy electric/electronic instrument etc. Normally, when the temperature is below a set value (Decided by multi-turn preset pot P1), voltage at the inverting input (pin2) of IC1 is lower than the level at the non-inverting terminal (pin3). So, the comparator output (at pin 6) of IC1 goes high and T1 is triggered to supply mains power to the desired heater element.

Electronic Heater Controller Circuit Schematic.



Note: CA3140 (IC2) is highly sensitive to electrostatic discharge (ESD). Please follow proper IC Handling Procedures.

When the temperature increases above the set value, say 50-60 degree centigrade, the inverting pin of IC1 also goes above the non-inverting pin and hence the comparator output falls. This stops triggering of T1 preventing the mains supply from reaching the heater element. Fortunately, the threshold value is user-controllable and can be set anywhere between 0 to 100 Degree centigrade.

The circuit works off stable 9Volt dc supply, which may be derived from the mains supply using a standard ac mains adaptor (100mA at 9V) or using a traditional capacitive voltage divider assembly. You can find such power circuits elsewhere in this website.
Read More..

Saturday, April 13, 2013

Reservoir Pump Controller

This circuit operates an automotive windscreen washer pump to fill a 20-litre drum from a 205-litre water reservoir. The drum is suspended above a drip line, which irrigates a vegetable backyard. Two chrome steel probes established within the drum act as sensors for the device. One probe is positioned at the excessive water mark, the other at about half-full. The pump power is switched with the aid of a 12V automotive relay (RLY1). Two op amps (IC1a & IC1b) linked as voltage comparators form the basis of the circuit. 

Initially, assume a falling water stage with the pump switched off. When the water level exposes the decrease probe, the non-inverting input (pin 5) of IC1b rises to about 7.4V. With trimpot VR2 correctly adjusted, this can be higher than the voltage on pin 6. The output (pin 7) therefore swings excessive, biasing Q1 into habitsion. This in turn result ins Q4 to behavior, switching on the relay and starting the pump. 

In addition, when Q4 switches on it supplies base current to Q3 by manner of a 6.8kO resistor. Initially, this current wafts throughout the 47µF capacitor, but once its base-emitter voltage reaches about zero.6V, Q3 behaviors. This action latches Q4 in the \"on\" state, because its base present can go with the flow to floor by implys of Q3 when Q1 ceases behavioring – on the method in which to occur when the rising water stage reaches the low probe. When the water degree reaches the high probe, the voltage on the non-inverting enter (pin 2) of IC1a decreases markedly as a outcome of the habitsivity of the water.

Circuit diagram:

Reservoir Pump Controller Circuit Diagram

If trimpot VR1 is appropriately adjusted, the output (pin 1) swings excessive, switching on Q2. This discharges the 47µF capacitor and robs Q3 of its base present, switching this transistor off. This in flip switches off Q4 and the relay. The zener diodes and 1kO collection resistors at the probe enters protect the op amp’s high impedance inputs from the effects of static discharge. The 47µF capacitor in parallel with the base-emitter junction of Q1 prevents the latching operate from being activated when energy is utilized to the circuit. The author’s setup is energyed from an previous car battery charged from a 12V solar panel.

http://www.ecircuitslab.com/2011/08/reservoir-pump-controller.html
Read More..

Sunday, April 7, 2013

Outdoor Lighting Controller

When you step out of your brightly-lit house  into the darkness, it takes a while for your  vision to adjust. A solution to this problem  is this outdoor light with automatic switch-off. As a bonus, it will also make it a little bit  easier to find the keyhole when returning  late at night. Often no mains neutral connection is avail-able at the point where the switch-off timer  is to be installed, which makes many circuit  arrangements impractical. However, the circuit here is designed to work in this situation. The design eschews bulky components such as transformers and the whole unit can  be built into a flush-mounted fitting. The circuit also features low quiescent current consumption.

Outdoor Lighting Controller Circuit Diagram :

Outdoor Lighting Controller-Circuit Diagram

The circuit is star ted by closing switch (or  pushbutton) S1. The lamp then immediately receives power via the bridge rectifier. The drop across diodes D5 to D10 is 4.2 V, which provides the power supply for the delay circuit itself, built around the CD4060 binary  counter.

When the switch is opened the lighting sup-ply current continues to flow through Tri1. The NPN optocoupler in the triac drive circuit detects when the triac is active, with antiparallel LED D1 keeping the drive sym-metrical. The NPN phototransistor inside the  coupler creates a reset pulse via T1, driving  pin 12 of the counter. This means that the  full time period will run even if the circuit is retriggered. The CD4060 counts at the AC grid frequency.  Pin 3 goes high after 213clocks, which corresponds to about 2.5 minutes. If this is not long  enough, a further CD4060 counter can be cascaded. T2 then turns on and shorts the internal LED of opto-triac IC2; this causes Tri1 to  be deprived of its trigger current and the light  goes out. The circuit remains without power until next triggered.

The circuit is only suitable for use with resistive loads. With the components shown (in particular in the bridge rectifier and D5 to  D10) the maximum total power of the connected bulb(s) is 200 watts. As is well known, the filament of the bulb is most likely to fail at the moment power is applied. There is little risk to Tri1 at this point as it is bridged by  the switch. The most likely consequence of overload is that one of diodes D1 to D6 will  fail. In the prototype no fuse was used, as it would not in any case have been easy to change. However, that is not necessarily recommended practice!

Circuits at AC line potential should only be constructed by suitably experienced persons and all relevant safety precautions and  applicable regulations must be observed during construction and installation.
Author : Harald Schad - Copyright : Elektor

Source  : http://www.ecircuitslab.com/2012/09/outdoor-lighting-controller.html

Read More..