2 Transistor Transmitter Schematic

A compact 2 transistor transmitter for use at VHF frequencies.

2 Transistor Transmitter Schematic Circuit Diagram

Notes:
Transistor T1 works as an audio preamplifier, gain is fixed at approximately R2/R1 or 100 times. The audio input is applied at the points LF in (on the diagram). P1 works as gain control. After amplification this audio signal now modulates the transmitter built around T2. Frequency is tunable using the trimmer CT and L1 is made using 3 turns of 1mm copper wire wound on a 5mm slug. The modulated signal passes via C6 to the antenna. A dipole can be made using 2 lengths of 65cm copper pipe. A DC power supply in the range 3 to 16 volts is required.

Read More..

How to Build a 2 to 4 Wire Audio Converter

This audio converter circuit maintains 40 dB of isolation between the two halves of entry and exit of a four-line son, while allowing a line connecting two son. A balancing potentiometer, R, adjusts the gain of zero lC2to crossing the inlet to the outlet .

The adjustment is done in terms of work just after installation by inserting a 1 kHz tone at the entrance of four son and setting R to the minimum output signal 82-ohm dummy-load resistor is placed between two wire terminals .

 2 to 4 Wire Audio Converter Circuit Diagram

Read More..

Simple 0 30 Volts 2 5A Variable Power Supply Circuit Diagram

This is the Simple 0-30 Volts - 2-5A Variable Power Supply Circuit Diagram. This is a high quality power supply with a continuously variable stabilized output adjustable between 0 and 30VDC. the LM 723 is the heart of the power supply which drives the BD137 and then the 2N3055. The circuit provides short circuit protection. And has great stability at voltage changes. Drive the circuit with 24 Volts 3A from a transformer. the 2N3055 needs a good heat sink.

  0-30 Volts - 2-5A Variable Power Supply Circuit Diagram

Read More..

Simple Wide band 2 pole high pass filter

The Simple Wide band 2 pole high-pass filter circuit provides a 10MHz cutoff frequency. Resistor R3 ensures that the input capacitance of the amplifier does not interact with the filter response at the frequency of interest. An equivalent low pass filter is similarly obtained by capacitance and resistance transformation . 

Simple Wide band 2 pole high-pass filter Circuit Diagram

Read More..

LM4990 2 Watt Audio Power Amplifier with Selectable Shutdown Logic Level

The LM4990 is an audio power amplifier primarily designed for demanding applications in mobile phones and other portable communication device applications. It is capable of delivering 1.25 watts of continuous average power to an 8Ω BTL load and 2 watts of continuous average power (LD and MH only) to a 4Ω BTL load with less than 1% distortion (THD+N+N) from a 5VDC power supply. Boomer audio power amplifiers were designed specifically to provide high quality output power with a minimal amount of external components. The LM4990 does not require output coupling capacitors or bootstrap capacitors, and therefore is ideally suited for mobile phone and other low voltage applications where minimal power consumption is a primary requirement.

Circuit Diagram :

  2 Watt Audio Power Amplifier with Selectable Shutdown Logic Level

The LM4990 features a low-power consumption shutdown mode. To facilitate this, Shutdown may be enabled by either logic high or low depending on mode selection. Driving the shutdown mode pin either high or low enables the shutdown pin to be driven in a likewise manner to enable shutdown. The LM4990 contains advanced pop & click circuitry which eliminates noise which would otherwise occur during turn-on and turn-off transitions. The LM4990 is unity-gain stable and can be configured by external gain-setting resistors.

 Features

Available in space-saving packages: LLP, Exposed-DAP TSSOP, MSOP, and ITL

Ultra low current shutdown mode

Improved pop & click circuitry eliminates noise during turn-on and turn-off transitions

2.2 - 5.5V operation

No output coupling capacitors, snubber networks or bootstrap capacitors required

Unity-gain stable

External gain configuration capability

User selectable shutdown High or Low logic Level
Key Specification

Improved PSRR at 217Hz & 1KHz	62dB
Power Output at 5.0V, 1% THD+N, 4Ω (LD and MH only)	2W (typ)
Power Output at 5.0V, 1% THD+N, 8Ω	1.25W (typ)
Power Output at 3.0V, 1% THD+N, 4Ω	600mW (typ)
Power Output at 3.0V, 1% THD+N, 8Ω	425mW (typ)
Shutdown Current	0.1µA (typ)

Applications

• Mobile Phones
• PDAs
• Portable electronic devices

Datasheets

Source: www.national.com

Read More..